DIY Boat Projects: Cleaning Aluminum

Fishing gets better when springtime brings warmth to Florida’s coastal waters. Better fishing means better catches, and cleaning tables often showcase a diverse mix of species, including spotted seatrout, sheepshead, redfish and small snappers.


Give your boat a facelift! Three-part series on DIY projects many boat owners can perform. This month: Clean and protect aluminum.

If you have a boat built for salt water, chances are that it has some type of welded aluminum structure, such as a tuna tower, T-top or poling platform.

If this “brightwork” is starting to show its age, there is a procedure that can bring back much of the original luster, plus add a layer of protection for
the future. The product I chose for this application is made by Showboat Custom Coating. It’s a clear ceramic coating that’s easy to apply. The only difficult part is making sure you prepare the metal surface correctly, without any shortcuts. Their website has very detailed instructions. Let’s look here at the basics:

On our subject boat we decided to replace the canvas top, so we went a bit further than we actually had to. In lieu of removing the canvas, we could have just untied it and flipped the edges out of the way. In either case, the first step is to remove anything that will not allow you to get to the full surface of the aluminum pipework.

When treating aluminum to bring back the luster, start by applying plastic sheeting and painters tape to protect surfaces around the aluminum.

Now you’re ready to start the process. First, tape off around the bases of the legs or supports with blue painter’s tape. Cover other areas of the boat with plastic sheeting—any areas that may be affected if some of the cleaning solution or coating drips.

Next step is to clean the aluminum surface with Soft Scrub and a Scotch Brite pad. Take your time throughout each process so no areas are missed, especially the welds.

Now you’ll need to etch the surface of the aluminum. For this, use wet and dry sandpaper. Use 2,000 grit for polished aluminum and 1,500 for a brushed finish. Take care around areas where the pads meet the fiberglass. This is where having taped off the pads pays off.

Before on the left, after on the right.

To degrease the aluminum, Dawn dishwashing soap works best. Use a microfiber cloth and lots of water. After all of the aluminum is thoroughly washed, it’s not a bad idea to wash areas around or under your aluminum to remove any residue from the wet sanding. Rinse everything down with a liberal amount of clean water and allow to air dry for at least one hour.

The final prep is to wipe down the aluminum with denatured alcohol. A spray bottle works best for this and again use a microfiber cloth to wipe. Allow the alcohol to dry for a minimum of 20 minutes.

Product Only: SB-230 $200 per pint For Showboat Custom Coating to do it: $950-$1,300

Now you’re ready to apply the SB-230, which is the clear ceramic coating. Well, almost ready. Check the forecast to make sure there’s no approaching rain in the area. The coating needs an hour to become tack free and you don’t want any water hitting the coating before it’s cured. If it does, it will create spots that are not easy to remove.

Applying the clear coating is simply a matter of soaking a small portion of a microfiber cloth and wiping onto the aluminum. Find a good place to start and end so you don’t miss any areas.

Allow the coating to completely dry then re-tie your canvas or install your new canvas. Now step back and admire your work.

What You’ll Need for One T-top

  • Non-powdered gloves
  • Protective eyewear
  • Tarp or plastic sheeting
  • 2″ blue painter’s tape
  • Soft Scrub (no bleach)
  • Scotch Brite pads (white)
  • Dawn dishwashing soap
  • Bucket
  • Water
  • Microfiber cloths
  • Spray bottle
  • Denatured alcohol

Next month, in part two of this series, we’ll go through the process of painting the hull sides using the roll-n-tip method. FS

First Published Florida Sportsman Magazine April 2019

Also in this months issue…

Life on the Edge

By Brenton Roberts
Determine what it is, where it is, and how to dissect it.

Discerning inshore edges: here, a high tide Spartina line.

Kayaks and Fly Fishing

By Mike Conner
Tips for making the most out of these versatile boats.

Writer with bluegill and largemouth bass. Pros and cons to fly fishing out of a kayak are discussed in the article.

To see more articles like this, and to catch the next part in this DIY series, subscribe here.

The post DIY Boat Projects: Cleaning Aluminum appeared first on Florida Sportsman.

Source: Florida Fisherman
DIY Boat Projects: Cleaning Aluminum

Leave a Reply